Setup Arduino in LG WebOS?

[ancylow]

Hi. Have installed HyperHDR with Piccap in my LG rooted. I have strip leds ws2812 with an Arduino (one of those kits from AliExpress). I have it working for a long time on a computer with libreelec and Hyperion.ng. And now I want to use it directly on my TV, but can't find the configuration to turn the leds on.
I appreciate your help, thanks.

[awawa-dev]

Hi
I doubt that WebOS has drivers for the serial port chips (UARTS) that usually come with Arduino, so your Arduino will not be detected and supported by the operating system unless you somehow provide the appropriate drivers for the kernel. Typically, the best results are achieved by using CDC-compatible boards, e.g. rp2040 (Pico -> HyperSerialPico), which are best supported by many versions of WebOS. You can then use them using the Adalight driver in HyperHDR. You'll definitely find more information on the OpenLGTV Discord server

[awawa-dev]

You can test rp2040 without a level shifter but try to use shortest as possible data cable between rp2040 and the LED strip (you need also to provide a common ground, do not connect +5V from the LED power supply to the rp2040! ). You should have a confirmation of communication between HyperHDR and rp2040 with HyperSerialPico at least.

[ancylow]

Well, device detected as Pico (/dev/ttyACM0), and leds on but.... only a few LEDs. This must be because of a low level voltage on gpi2?

[awawa-dev]

Do the LEDs that are lit react to changes when, for example, you set the selected color in the effects (remote tab) in HyperHDR, or are they phantoms? Have you connected LED strip ground to rp2040 ground? What's in the full HyperHDR logs?

[ancylow]

Yes, they change of colour, but blinks a little, is not a solid colour.
GND strip is connected to GND pin of RP2040.

And this is the log:
Registros
2024-04-22T20:11:15.869Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:218) productIdentifier: 0xa
2024-04-22T20:11:15.869Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:219) vendorIdentifier: 0x2e8a
2024-04-22T20:11:15.869Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:220) serialNumber: E6611032E3645232
2024-04-22T20:11:15.877Z [LEDDEVICE0_ADALIGHT] Detected Rp2040 type board. HyperHDR skips the reset. State: 1, 1
2024-04-22T20:11:15.880Z [LEDDEVICE0_ADALIGHT] DETECTED DEVICE USING HyperSerialEsp8266/HyperSerialESP32/HyperSerialPico FIRMWARE (HyperHDR frames: 0 (FPS), receiv.: 0, good: 0, incompl.: 0, mem1: 0, mem2: 448, heap: 123232 Welcome! Awa driver 9.) at 2 msec
2024-04-22T20:11:15.880Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:64) Switch on
2024-04-22T20:11:15.880Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:140) Power On
2024-04-22T20:11:15.880Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:367) Starting timer with interval = 20ms
2024-04-22T20:11:15.880Z [COMPONENTCTRL0] LED device: enabled
2024-04-22T20:11:28.225Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:286) Stop device
2024-04-22T20:11:28.225Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:381) Stopping refresh timer
2024-04-22T20:11:28.225Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:297) Disable the device
2024-04-22T20:11:28.225Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:90) Switch off
2024-04-22T20:11:28.225Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:544) Set LED strip to black/power off
2024-04-22T20:11:28.229Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:146) Flush was successful
2024-04-22T20:11:28.238Z [LEDDEVICE0_ADALIGHT] Received goodbye: 'HyperHDR frames: 50 (FPS), receiv.: 50, good: 50, incompl.: 0, mem1: 0, mem2: 448, heap: 123232
' (97)
2024-04-22T20:11:28.245Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:164) Serial port is closed: ttyACM0
2024-04-22T20:11:28.245Z [LEDDEVICE0_ADALIGHT] Stopped LedDevice 'adalight'
2024-04-22T20:11:28.247Z [LEDDEVICE0_ADALIGHT] Start LedDevice 'adalight'.
2024-04-22T20:11:28.247Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:337) deviceConfig: [{"awa_mode":true,"colorOrder":"rgb","currentLedCount":135,"espHandshake":true,"forceSerialDetection":false,"hardwareLedCount":null,"maxRetry":5,"output":"ttyACM0","rate":1,"refreshTime":20,"smoothingRefreshTime":20,"type":"adalight","white_channel_calibration":false}]
2024-04-22T20:11:28.247Z [LEDDEVICE0_ADALIGHT] Ignoring user LED refresh rate. Forcing smoothing refresh rate = 50.00 Hz
2024-04-22T20:11:28.247Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:423) Refresh rate = 50.00 Hz
2024-04-22T20:11:28.247Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:373) Device is not ready to start a timer
2024-04-22T20:11:28.247Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:433) Refresh interval updated to 20ms
2024-04-22T20:11:28.247Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:50) DeviceType : adalight
2024-04-22T20:11:28.247Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:51) LedCount : 135
2024-04-22T20:11:28.247Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:52) RefreshTime : 20
2024-04-22T20:11:28.248Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:67) Device name : ttyACM0
2024-04-22T20:11:28.248Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:68) Auto selection: 0
2024-04-22T20:11:28.248Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:69) Baud rate : 1
2024-04-22T20:11:28.248Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:70) ESP handshake : ON
2024-04-22T20:11:28.248Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:71) Force ESP/Pico Detection : OFF
2024-04-22T20:11:28.248Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:72) Delayed open : 0
2024-04-22T20:11:28.248Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:73) Retry limit : 5
2024-04-22T20:11:28.248Z [LEDDEVICE0_ADALIGHT] The refresh timer is enabled ('Refresh time' > 0) and may limit the performance of the LED driver. Ignore this error if you set it on purpose for some reason (but you almost never need it).
2024-04-22T20:11:28.248Z [LEDDEVICE0_ADALIGHT] (LedDeviceAdalight.cpp:79) Adalight driver with activated high speeed & data integration check AWA protocol
2024-04-22T20:11:28.248Z [LEDDEVICE0_ADALIGHT] (LedDeviceAdalight.cpp:88) Adalight header for 135 leds: Awa 0x00 0x86 0xd3
2024-04-22T20:11:28.248Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:247) Enable the device
2024-04-22T20:11:28.248Z [LEDDEVICE0_ADALIGHT] Opening UART: ttyACM0
2024-04-22T20:11:28.248Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:209) _serialPort.open(QIODevice::ReadWrite): ttyACM0, Baud rate [1]bps
2024-04-22T20:11:28.255Z [COMPONENTCTRL0] LED device: disabled
2024-04-22T20:11:28.293Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:214) portName: ttyACM0
2024-04-22T20:11:28.293Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:215) systemLocation: /dev/ttyACM0
2024-04-22T20:11:28.293Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:216) description: Pico
2024-04-22T20:11:28.293Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:217) manufacturer: Raspberry Pi
2024-04-22T20:11:28.293Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:218) productIdentifier: 0xa
2024-04-22T20:11:28.293Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:219) vendorIdentifier: 0x2e8a
2024-04-22T20:11:28.293Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:220) serialNumber: E6611032E3645232
2024-04-22T20:11:28.299Z [LEDDEVICE0_ADALIGHT] Detected Rp2040 type board. HyperHDR skips the reset. State: 1, 1
2024-04-22T20:11:28.303Z [LEDDEVICE0_ADALIGHT] DETECTED DEVICE USING HyperSerialEsp8266/HyperSerialESP32/HyperSerialPico FIRMWARE (HyperHDR frames: 0 (FPS), receiv.: 0, good: 0, incompl.: 0, mem1: 0, mem2: 448, heap: 123232 Welcome! Awa driver 9.) at 3 msec
2024-04-22T20:11:28.303Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:64) Switch on
2024-04-22T20:11:28.303Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:140) Power On
2024-04-22T20:11:28.303Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:367) Starting timer with interval = 20ms
2024-04-22T20:11:28.303Z [COMPONENTCTRL0] LED device: enabled
2024-04-22T20:11:39.422Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:286) Stop device
2024-04-22T20:11:39.422Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:381) Stopping refresh timer
2024-04-22T20:11:39.423Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:297) Disable the device
2024-04-22T20:11:39.423Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:90) Switch off
2024-04-22T20:11:39.423Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:544) Set LED strip to black/power off
2024-04-22T20:11:39.427Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:146) Flush was successful
2024-04-22T20:11:39.435Z [LEDDEVICE0_ADALIGHT] Received goodbye: 'HyperHDR frames: 50 (FPS), receiv.: 50, good: 50, incompl.: 0, mem1: 0, mem2: 448, heap: 123232
' (97)
2024-04-22T20:11:39.441Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:164) Serial port is closed: ttyACM0
2024-04-22T20:11:39.441Z [LEDDEVICE0_ADALIGHT] Stopped LedDevice 'adalight'
2024-04-22T20:11:39.442Z [LEDDEVICE0_ADALIGHT] Start LedDevice 'adalight'.
2024-04-22T20:11:39.442Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:337) deviceConfig: [{"awa_mode":true,"colorOrder":"rgb","currentLedCount":135,"espHandshake":true,"forceSerialDetection":false,"hardwareLedCount":null,"maxRetry":5,"output":"ttyACM0","rate":200000,"refreshTime":20,"smoothingRefreshTime":20,"type":"adalight","white_channel_calibration":false}]
2024-04-22T20:11:39.442Z [LEDDEVICE0_ADALIGHT] Ignoring user LED refresh rate. Forcing smoothing refresh rate = 50.00 Hz
2024-04-22T20:11:39.442Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:423) Refresh rate = 50.00 Hz
2024-04-22T20:11:39.442Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:373) Device is not ready to start a timer
2024-04-22T20:11:39.442Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:433) Refresh interval updated to 20ms
2024-04-22T20:11:39.443Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:50) DeviceType : adalight
2024-04-22T20:11:39.443Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:51) LedCount : 135
2024-04-22T20:11:39.443Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:52) RefreshTime : 20
2024-04-22T20:11:39.443Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:67) Device name : ttyACM0
2024-04-22T20:11:39.443Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:68) Auto selection: 0
2024-04-22T20:11:39.443Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:69) Baud rate : 200000
2024-04-22T20:11:39.443Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:70) ESP handshake : ON
2024-04-22T20:11:39.443Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:71) Force ESP/Pico Detection : OFF
2024-04-22T20:11:39.443Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:72) Delayed open : 0
2024-04-22T20:11:39.443Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:73) Retry limit : 5
2024-04-22T20:11:39.443Z [LEDDEVICE0_ADALIGHT] The refresh timer is enabled ('Refresh time' > 0) and may limit the performance of the LED driver. Ignore this error if you set it on purpose for some reason (but you almost never need it).
2024-04-22T20:11:39.443Z [LEDDEVICE0_ADALIGHT] (LedDeviceAdalight.cpp:79) Adalight driver with activated high speeed & data integration check AWA protocol
2024-04-22T20:11:39.443Z [LEDDEVICE0_ADALIGHT] (LedDeviceAdalight.cpp:88) Adalight header for 135 leds: Awa 0x00 0x86 0xd3
2024-04-22T20:11:39.443Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:247) Enable the device
2024-04-22T20:11:39.443Z [LEDDEVICE0_ADALIGHT] Opening UART: ttyACM0
2024-04-22T20:11:39.443Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:209) _serialPort.open(QIODevice::ReadWrite): ttyACM0, Baud rate [200000]bps
2024-04-22T20:11:39.450Z [COMPONENTCTRL0] LED device: disabled
2024-04-22T20:11:39.492Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:214) portName: ttyACM0
2024-04-22T20:11:39.492Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:215) systemLocation: /dev/ttyACM0
2024-04-22T20:11:39.492Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:216) description: Pico
2024-04-22T20:11:39.492Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:217) manufacturer: Raspberry Pi
2024-04-22T20:11:39.492Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:218) productIdentifier: 0xa
2024-04-22T20:11:39.493Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:219) vendorIdentifier: 0x2e8a
2024-04-22T20:11:39.493Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:220) serialNumber: E6611032E3645232
2024-04-22T20:11:39.497Z [LEDDEVICE0_ADALIGHT] Detected Rp2040 type board. HyperHDR skips the reset. State: 1, 1
2024-04-22T20:11:39.500Z [LEDDEVICE0_ADALIGHT] DETECTED DEVICE USING HyperSerialEsp8266/HyperSerialESP32/HyperSerialPico FIRMWARE (HyperHDR frames: 0 (FPS), receiv.: 0, good: 0, incompl.: 0, mem1: 0, mem2: 448, heap: 123232 Welcome! Awa driver 9.) at 2 msec
2024-04-22T20:11:39.500Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:64) Switch on
2024-04-22T20:11:39.500Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:140) Power On
2024-04-22T20:11:39.500Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:367) Starting timer with interval = 20ms
2024-04-22T20:11:39.502Z [COMPONENTCTRL0] LED device: enabled
2024-04-22T20:12:30.518Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:286) Stop device
2024-04-22T20:12:30.518Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:381) Stopping refresh timer
2024-04-22T20:12:30.518Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:297) Disable the device
2024-04-22T20:12:30.518Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:90) Switch off
2024-04-22T20:12:30.518Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:544) Set LED strip to black/power off
2024-04-22T20:12:30.521Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:146) Flush was successful
2024-04-22T20:12:30.530Z [LEDDEVICE0_ADALIGHT] Received goodbye: 'HyperHDR frames: 52 (FPS), receiv.: 51, good: 51, incompl.: 0, mem1: 0, mem2: 450, heap: 123232
' (97)
2024-04-22T20:12:30.536Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:164) Serial port is closed: ttyACM0
2024-04-22T20:12:30.536Z [LEDDEVICE0_ADALIGHT] Stopped LedDevice 'adalight'
2024-04-22T20:12:30.536Z [LEDDEVICE0_ADALIGHT] Start LedDevice 'adalight'.
2024-04-22T20:12:30.537Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:337) deviceConfig: [{"awa_mode":true,"colorOrder":"rgb","currentLedCount":135,"espHandshake":false,"forceSerialDetection":false,"hardwareLedCount":null,"maxRetry":5,"output":"ttyACM0","rate":200000,"refreshTime":20,"smoothingRefreshTime":20,"type":"adalight","white_channel_calibration":false}]
2024-04-22T20:12:30.537Z [LEDDEVICE0_ADALIGHT] Ignoring user LED refresh rate. Forcing smoothing refresh rate = 50.00 Hz
2024-04-22T20:12:30.537Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:423) Refresh rate = 50.00 Hz
2024-04-22T20:12:30.537Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:373) Device is not ready to start a timer
2024-04-22T20:12:30.537Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:433) Refresh interval updated to 20ms
2024-04-22T20:12:30.537Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:50) DeviceType : adalight
2024-04-22T20:12:30.537Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:51) LedCount : 135
2024-04-22T20:12:30.537Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:52) RefreshTime : 20
2024-04-22T20:12:30.537Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:67) Device name : ttyACM0
2024-04-22T20:12:30.537Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:68) Auto selection: 0
2024-04-22T20:12:30.537Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:69) Baud rate : 200000
2024-04-22T20:12:30.537Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:70) ESP handshake : OFF
2024-04-22T20:12:30.537Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:71) Force ESP/Pico Detection : OFF
2024-04-22T20:12:30.537Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:72) Delayed open : 0
2024-04-22T20:12:30.537Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:73) Retry limit : 5
2024-04-22T20:12:30.537Z [LEDDEVICE0_ADALIGHT] The refresh timer is enabled ('Refresh time' > 0) and may limit the performance of the LED driver. Ignore this error if you set it on purpose for some reason (but you almost never need it).
2024-04-22T20:12:30.537Z [LEDDEVICE0_ADALIGHT] (LedDeviceAdalight.cpp:79) Adalight driver with activated high speeed & data integration check AWA protocol
2024-04-22T20:12:30.537Z [LEDDEVICE0_ADALIGHT] (LedDeviceAdalight.cpp:88) Adalight header for 135 leds: Awa 0x00 0x86 0xd3
2024-04-22T20:12:30.537Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:247) Enable the device
2024-04-22T20:12:30.537Z [LEDDEVICE0_ADALIGHT] Opening UART: ttyACM0
2024-04-22T20:12:30.537Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:209) _serialPort.open(QIODevice::ReadWrite): ttyACM0, Baud rate [200000]bps
2024-04-22T20:12:30.543Z [COMPONENTCTRL0] LED device: disabled
2024-04-22T20:12:30.588Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:214) portName: ttyACM0
2024-04-22T20:12:30.588Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:215) systemLocation: /dev/ttyACM0
2024-04-22T20:12:30.588Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:216) description: Pico
2024-04-22T20:12:30.588Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:217) manufacturer: Raspberry Pi
2024-04-22T20:12:30.588Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:218) productIdentifier: 0xa
2024-04-22T20:12:30.588Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:219) vendorIdentifier: 0x2e8a
2024-04-22T20:12:30.588Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:220) serialNumber: E6611032E3645232
2024-04-22T20:12:30.594Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:64) Switch on
2024-04-22T20:12:30.594Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:140) Power On
2024-04-22T20:12:30.594Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:367) Starting timer with interval = 20ms
2024-04-22T20:12:30.595Z [COMPONENTCTRL0] LED device: enabled
2024-04-22T20:12:35.585Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:286) Stop device
2024-04-22T20:12:35.585Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:381) Stopping refresh timer
2024-04-22T20:12:35.585Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:297) Disable the device
2024-04-22T20:12:35.585Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:90) Switch off
2024-04-22T20:12:35.585Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:544) Set LED strip to black/power off
2024-04-22T20:12:35.589Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:146) Flush was successful
2024-04-22T20:12:35.596Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:164) Serial port is closed: ttyACM0
2024-04-22T20:12:35.596Z [LEDDEVICE0_ADALIGHT] Stopped LedDevice 'adalight'
2024-04-22T20:12:35.597Z [LEDDEVICE0_ADALIGHT] Start LedDevice 'adalight'.
2024-04-22T20:12:35.597Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:337) deviceConfig: [{"awa_mode":true,"colorOrder":"rgb","currentLedCount":135,"espHandshake":true,"forceSerialDetection":false,"hardwareLedCount":null,"maxRetry":5,"output":"ttyACM0","rate":200000,"refreshTime":20,"smoothingRefreshTime":20,"type":"adalight","white_channel_calibration":false}]
2024-04-22T20:12:35.597Z [LEDDEVICE0_ADALIGHT] Ignoring user LED refresh rate. Forcing smoothing refresh rate = 50.00 Hz
2024-04-22T20:12:35.597Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:423) Refresh rate = 50.00 Hz
2024-04-22T20:12:35.597Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:373) Device is not ready to start a timer
2024-04-22T20:12:35.597Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:433) Refresh interval updated to 20ms
2024-04-22T20:12:35.597Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:50) DeviceType : adalight
2024-04-22T20:12:35.597Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:51) LedCount : 135
2024-04-22T20:12:35.597Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:52) RefreshTime : 20
2024-04-22T20:12:35.597Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:67) Device name : ttyACM0
2024-04-22T20:12:35.597Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:68) Auto selection: 0
2024-04-22T20:12:35.597Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:69) Baud rate : 200000
2024-04-22T20:12:35.597Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:70) ESP handshake : ON
2024-04-22T20:12:35.597Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:71) Force ESP/Pico Detection : OFF
2024-04-22T20:12:35.597Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:72) Delayed open : 0
2024-04-22T20:12:35.597Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:73) Retry limit : 5
2024-04-22T20:12:35.597Z [LEDDEVICE0_ADALIGHT] The refresh timer is enabled ('Refresh time' > 0) and may limit the performance of the LED driver. Ignore this error if you set it on purpose for some reason (but you almost never need it).
2024-04-22T20:12:35.597Z [LEDDEVICE0_ADALIGHT] (LedDeviceAdalight.cpp:79) Adalight driver with activated high speeed & data integration check AWA protocol
2024-04-22T20:12:35.597Z [LEDDEVICE0_ADALIGHT] (LedDeviceAdalight.cpp:88) Adalight header for 135 leds: Awa 0x00 0x86 0xd3
2024-04-22T20:12:35.597Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:247) Enable the device
2024-04-22T20:12:35.597Z [LEDDEVICE0_ADALIGHT] Opening UART: ttyACM0
2024-04-22T20:12:35.597Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:209) _serialPort.open(QIODevice::ReadWrite): ttyACM0, Baud rate [200000]bps
2024-04-22T20:12:35.602Z [COMPONENTCTRL0] LED device: disabled
2024-04-22T20:12:35.684Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:214) portName: ttyACM0
2024-04-22T20:12:35.684Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:215) systemLocation: /dev/ttyACM0
2024-04-22T20:12:35.684Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:216) description: Pico
2024-04-22T20:12:35.684Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:217) manufacturer: Raspberry Pi
2024-04-22T20:12:35.684Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:218) productIdentifier: 0xa
2024-04-22T20:12:35.684Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:219) vendorIdentifier: 0x2e8a
2024-04-22T20:12:35.684Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:220) serialNumber: E6611032E3645232
2024-04-22T20:12:35.690Z [LEDDEVICE0_ADALIGHT] Detected Rp2040 type board. HyperHDR skips the reset. State: 1, 1
2024-04-22T20:12:35.693Z [LEDDEVICE0_ADALIGHT] DETECTED DEVICE USING HyperSerialEsp8266/HyperSerialESP32/HyperSerialPico FIRMWARE (HyperHDR frames: 50 (FPS), receiv.: 50, good: 50, incompl.: 0, mem1: 0, mem2: 450, heap: 123232 Welcome! Awa driver 9.) at 3 msec
2024-04-22T20:12:35.693Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:64) Switch on
2024-04-22T20:12:35.694Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:140) Power On
2024-04-22T20:12:35.694Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:367) Starting timer with interval = 20ms
2024-04-22T20:12:35.694Z [COMPONENTCTRL0] LED device: enabled
2024-04-22T20:12:39.451Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:286) Stop device
2024-04-22T20:12:39.451Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:381) Stopping refresh timer
2024-04-22T20:12:39.451Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:297) Disable the device
2024-04-22T20:12:39.451Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:90) Switch off
2024-04-22T20:12:39.451Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:544) Set LED strip to black/power off
2024-04-22T20:12:39.455Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:146) Flush was successful
2024-04-22T20:12:39.463Z [LEDDEVICE0_ADALIGHT] Received goodbye: 'HyperHDR frames: 50 (FPS), receiv.: 50, good: 50, incompl.: 0, mem1: 0, mem2: 450, heap: 123232
' (97)
2024-04-22T20:12:39.472Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:164) Serial port is closed: ttyACM0
2024-04-22T20:12:39.472Z [LEDDEVICE0_ADALIGHT] Stopped LedDevice 'adalight'
2024-04-22T20:12:39.472Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:286) Stop device
2024-04-22T20:12:39.472Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:297) Disable the device
2024-04-22T20:12:39.472Z [LEDDEVICE0_ADALIGHT] Stopped LedDevice 'adalight'
2024-04-22T20:12:39.473Z [LEDDEVICE0_ADALIGHT] Start LedDevice 'adalight'.
2024-04-22T20:12:39.473Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:337) deviceConfig: [{"awa_mode":false,"colorOrder":"rgb","currentLedCount":135,"hardwareLedCount":null,"maxRetry":5,"output":"ttyACM0","rate":200000,"refreshTime":20,"smoothingRefreshTime":20,"type":"adalight"}]
2024-04-22T20:12:39.474Z [LEDDEVICE0_ADALIGHT] Ignoring user LED refresh rate. Forcing smoothing refresh rate = 50.00 Hz
2024-04-22T20:12:39.475Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:423) Refresh rate = 50.00 Hz
2024-04-22T20:12:39.475Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:373) Device is not ready to start a timer
2024-04-22T20:12:39.475Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:433) Refresh interval updated to 20ms
2024-04-22T20:12:39.475Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:50) DeviceType : adalight
2024-04-22T20:12:39.475Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:51) LedCount : 135
2024-04-22T20:12:39.475Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:52) RefreshTime : 20
2024-04-22T20:12:39.475Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:67) Device name : ttyACM0
2024-04-22T20:12:39.475Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:68) Auto selection: 0
2024-04-22T20:12:39.475Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:69) Baud rate : 200000
2024-04-22T20:12:39.475Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:70) ESP handshake : OFF
2024-04-22T20:12:39.475Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:71) Force ESP/Pico Detection : OFF
2024-04-22T20:12:39.475Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:72) Delayed open : 0
2024-04-22T20:12:39.475Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:73) Retry limit : 5
2024-04-22T20:12:39.475Z [LEDDEVICE0_ADALIGHT] The refresh timer is enabled ('Refresh time' > 0) and may limit the performance of the LED driver. Ignore this error if you set it on purpose for some reason (but you almost never need it).
2024-04-22T20:12:39.475Z [LEDDEVICE0_ADALIGHT] (LedDeviceAdalight.cpp:88) Adalight header for 135 leds: Ada 0x00 0x86 0xd3
2024-04-22T20:12:39.475Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:247) Enable the device
2024-04-22T20:12:39.475Z [LEDDEVICE0_ADALIGHT] Opening UART: ttyACM0
2024-04-22T20:12:39.475Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:209) _serialPort.open(QIODevice::ReadWrite): ttyACM0, Baud rate [200000]bps
2024-04-22T20:12:39.485Z [COMPONENTCTRL0] LED device: disabled
2024-04-22T20:12:39.548Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:214) portName: ttyACM0
2024-04-22T20:12:39.548Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:215) systemLocation: /dev/ttyACM0
2024-04-22T20:12:39.548Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:216) description: Pico
2024-04-22T20:12:39.548Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:217) manufacturer: Raspberry Pi
2024-04-22T20:12:39.548Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:218) productIdentifier: 0xa
2024-04-22T20:12:39.548Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:219) vendorIdentifier: 0x2e8a
2024-04-22T20:12:39.548Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:220) serialNumber: E6611032E3645232
2024-04-22T20:12:39.565Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:64) Switch on
2024-04-22T20:12:39.565Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:140) Power On
2024-04-22T20:12:39.566Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:367) Starting timer with interval = 20ms
2024-04-22T20:12:39.566Z [COMPONENTCTRL0] LED device: enabled
2024-04-22T20:12:48.253Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:286) Stop device
2024-04-22T20:12:48.253Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:381) Stopping refresh timer
2024-04-22T20:12:48.253Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:297) Disable the device
2024-04-22T20:12:48.253Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:90) Switch off
2024-04-22T20:12:48.253Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:544) Set LED strip to black/power off
2024-04-22T20:12:48.257Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:146) Flush was successful
2024-04-22T20:12:48.263Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:164) Serial port is closed: ttyACM0
2024-04-22T20:12:48.263Z [LEDDEVICE0_ADALIGHT] Stopped LedDevice 'adalight'
2024-04-22T20:12:48.263Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:286) Stop device
2024-04-22T20:12:48.263Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:297) Disable the device
2024-04-22T20:12:48.263Z [LEDDEVICE0_ADALIGHT] Stopped LedDevice 'adalight'
2024-04-22T20:12:48.264Z [LEDDEVICE0_ADALIGHT] Start LedDevice 'adalight'.
2024-04-22T20:12:48.264Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:337) deviceConfig: [{"awa_mode":false,"colorOrder":"rgb","currentLedCount":135,"hardwareLedCount":null,"maxRetry":5,"output":"ttyS0","rate":200000,"refreshTime":20,"smoothingRefreshTime":20,"type":"adalight"}]
2024-04-22T20:12:48.264Z [LEDDEVICE0_ADALIGHT] Ignoring user LED refresh rate. Forcing smoothing refresh rate = 50.00 Hz
2024-04-22T20:12:48.264Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:423) Refresh rate = 50.00 Hz
2024-04-22T20:12:48.264Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:373) Device is not ready to start a timer
2024-04-22T20:12:48.264Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:433) Refresh interval updated to 20ms
2024-04-22T20:12:48.264Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:50) DeviceType : adalight
2024-04-22T20:12:48.264Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:51) LedCount : 135
2024-04-22T20:12:48.264Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:52) RefreshTime : 20
2024-04-22T20:12:48.264Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:67) Device name : ttyS0
2024-04-22T20:12:48.264Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:68) Auto selection: 0
2024-04-22T20:12:48.264Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:69) Baud rate : 200000
2024-04-22T20:12:48.264Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:70) ESP handshake : OFF
2024-04-22T20:12:48.264Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:71) Force ESP/Pico Detection : OFF
2024-04-22T20:12:48.264Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:72) Delayed open : 0
2024-04-22T20:12:48.264Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:73) Retry limit : 5
2024-04-22T20:12:48.264Z [LEDDEVICE0_ADALIGHT] The refresh timer is enabled ('Refresh time' > 0) and may limit the performance of the LED driver. Ignore this error if you set it on purpose for some reason (but you almost never need it).
2024-04-22T20:12:48.264Z [LEDDEVICE0_ADALIGHT] (LedDeviceAdalight.cpp:88) Adalight header for 135 leds: Ada 0x00 0x86 0xd3
2024-04-22T20:12:48.264Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:247) Enable the device
2024-04-22T20:12:48.264Z [LEDDEVICE0_ADALIGHT] Opening UART: ttyS0
2024-04-22T20:12:48.264Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:209) _serialPort.open(QIODevice::ReadWrite): ttyS0, Baud rate [200000]bps
2024-04-22T20:12:48.271Z [COMPONENTCTRL0] LED device: disabled
2024-04-22T20:12:48.310Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:214) portName: ttyS0
2024-04-22T20:12:48.310Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:215) systemLocation: /dev/ttyS0
2024-04-22T20:12:48.310Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:216) description:
2024-04-22T20:12:48.310Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:217) manufacturer:
2024-04-22T20:12:48.310Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:218) productIdentifier: 0x0
2024-04-22T20:12:48.310Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:219) vendorIdentifier: 0x0
2024-04-22T20:12:48.310Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:220) serialNumber:
2024-04-22T20:12:48.319Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:64) Switch on
2024-04-22T20:12:48.319Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:140) Power On
2024-04-22T20:12:48.319Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:367) Starting timer with interval = 20ms
2024-04-22T20:12:48.320Z [COMPONENTCTRL0] LED device: enabled
2024-04-22T20:12:55.183Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:286) Stop device
2024-04-22T20:12:55.183Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:381) Stopping refresh timer
2024-04-22T20:12:55.183Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:297) Disable the device
2024-04-22T20:12:55.183Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:90) Switch off
2024-04-22T20:12:55.183Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:544) Set LED strip to black/power off
2024-04-22T20:12:55.227Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:146) Flush was successful
2024-04-22T20:12:55.227Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:164) Serial port is closed: ttyS0
2024-04-22T20:12:55.227Z [LEDDEVICE0_ADALIGHT] Stopped LedDevice 'adalight'
2024-04-22T20:12:55.228Z [LEDDEVICE0_ADALIGHT] Start LedDevice 'adalight'.
2024-04-22T20:12:55.229Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:337) deviceConfig: [{"awa_mode":true,"colorOrder":"rgb","currentLedCount":135,"espHandshake":true,"forceSerialDetection":false,"hardwareLedCount":null,"maxRetry":5,"output":"ttyACM0","rate":200000,"refreshTime":20,"smoothingRefreshTime":20,"type":"adalight","white_channel_calibration":false}]
2024-04-22T20:12:55.229Z [LEDDEVICE0_ADALIGHT] Ignoring user LED refresh rate. Forcing smoothing refresh rate = 50.00 Hz
2024-04-22T20:12:55.229Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:423) Refresh rate = 50.00 Hz
2024-04-22T20:12:55.229Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:373) Device is not ready to start a timer
2024-04-22T20:12:55.229Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:433) Refresh interval updated to 20ms
2024-04-22T20:12:55.229Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:50) DeviceType : adalight
2024-04-22T20:12:55.229Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:51) LedCount : 135
2024-04-22T20:12:55.229Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:52) RefreshTime : 20
2024-04-22T20:12:55.230Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:67) Device name : ttyACM0
2024-04-22T20:12:55.230Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:68) Auto selection: 0
2024-04-22T20:12:55.230Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:69) Baud rate : 200000
2024-04-22T20:12:55.230Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:70) ESP handshake : ON
2024-04-22T20:12:55.230Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:71) Force ESP/Pico Detection : OFF
2024-04-22T20:12:55.230Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:72) Delayed open : 0
2024-04-22T20:12:55.230Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:73) Retry limit : 5
2024-04-22T20:12:55.230Z [LEDDEVICE0_ADALIGHT] The refresh timer is enabled ('Refresh time' > 0) and may limit the performance of the LED driver. Ignore this error if you set it on purpose for some reason (but you almost never need it).
2024-04-22T20:12:55.230Z [LEDDEVICE0_ADALIGHT] (LedDeviceAdalight.cpp:79) Adalight driver with activated high speeed & data integration check AWA protocol
2024-04-22T20:12:55.230Z [LEDDEVICE0_ADALIGHT] (LedDeviceAdalight.cpp:88) Adalight header for 135 leds: Awa 0x00 0x86 0xd3
2024-04-22T20:12:55.230Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:247) Enable the device
2024-04-22T20:12:55.230Z [LEDDEVICE0_ADALIGHT] Opening UART: ttyACM0
2024-04-22T20:12:55.230Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:209) _serialPort.open(QIODevice::ReadWrite): ttyACM0, Baud rate [200000]bps
2024-04-22T20:12:55.238Z [COMPONENTCTRL0] LED device: disabled
2024-04-22T20:12:55.276Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:214) portName: ttyACM0
2024-04-22T20:12:55.276Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:215) systemLocation: /dev/ttyACM0
2024-04-22T20:12:55.276Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:216) description: Pico
2024-04-22T20:12:55.276Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:217) manufacturer: Raspberry Pi
2024-04-22T20:12:55.276Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:218) productIdentifier: 0xa
2024-04-22T20:12:55.277Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:219) vendorIdentifier: 0x2e8a
2024-04-22T20:12:55.277Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:220) serialNumber: E6611032E3645232
2024-04-22T20:12:55.281Z [LEDDEVICE0_ADALIGHT] Detected Rp2040 type board. HyperHDR skips the reset. State: 1, 1
2024-04-22T20:12:55.284Z [LEDDEVICE0_ADALIGHT] DETECTED DEVICE USING HyperSerialEsp8266/HyperSerialESP32/HyperSerialPico FIRMWARE (HyperHDR frames: 0 (FPS), receiv.: 0, good: 0, incompl.: 0, mem1: 0, mem2: 448, heap: 123232 Welcome! Awa driver 9.) at 2 msec
2024-04-22T20:12:55.285Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:64) Switch on
2024-04-22T20:12:55.285Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:140) Power On
2024-04-22T20:12:55.285Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:367) Starting timer with interval = 20ms
2024-04-22T20:12:55.285Z [COMPONENTCTRL0] LED device: enabled
2024-04-22T20:13:03.656Z [WEBSOCKET] (HyperAPI.cpp:1109) message: [{"command":"leddevice","ledDeviceType":"","params":{},"subcommand":"hasLedClock","tan":1}]
2024-04-22T20:13:12.602Z [SMOOTHING0] High resolution clock is NOT STEADY!
2024-04-22T20:13:12.602Z [SMOOTHING0] Clearing queued colors before: disabling
2024-04-22T20:13:12.602Z [SMOOTHING0] Smoothing queue is cleared
2024-04-22T20:13:12.602Z [COMPONENTCTRL0] Smoothing: disabled
2024-04-22T20:13:12.602Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:381) Stopping refresh timer
2024-04-22T20:13:12.602Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:423) Refresh rate = 50.00 Hz
2024-04-22T20:13:12.602Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:367) Starting timer with interval = 20ms
2024-04-22T20:13:12.602Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:433) Refresh interval updated to 20ms
2024-04-22T20:13:12.602Z [SMOOTHING0] Creating config (0) => type: Alternative, dirMode: false, pause: false, settlingTime: 150ms, interval: 20ms (50Hz), antiFlickTres: 32, antiFlickStep: 2, antiFlickTime: 250
2024-04-22T20:13:12.602Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:448) LED refresh interval adjustment caused by smoothing configuration change to 20ms (proposed: 0ms)
2024-04-22T20:13:12.602Z [SMOOTHING0] Selecting config (0) => type: Alternative, directMode: false, pause: false, settlingTime: 150ms, interval: 20ms (50Hz), antiFlickTres: 32, antiFlickStep: 2, antiFlickTime: 250
2024-04-22T20:13:34.553Z [MUXER0] Register new input 'Web Configuration@::ffff:192.168.1.45/COLOR' with priority 1 as inactive
2024-04-22T20:13:34.553Z [MUXER0] Priority 1 is now active
2024-04-22T20:13:34.553Z [MUXER0] Set visible priority to 1
2024-04-22T20:13:34.553Z [HYPERHDR0] New priority[1], previous [150]
2024-04-22T20:13:34.553Z [COLORSPACE_CALIBRATION0] (ColorSpaceCalibration.cpp:225) setBackLightEnabled: 0
2024-04-22T20:13:38.257Z [FLATBUFSERVER] (FlatBufferClient.cpp:92) Socket Closed
2024-04-22T20:13:38.257Z [MUXER0] Removed source priority 150
2024-04-22T20:13:38.260Z [MUXER0] Register new input 'webos@::ffff:127.0.0.1/FLATBUFSERVER' with priority 150 as inactive
2024-04-22T20:13:38.260Z [MUXER0] Priority 150 is now active
2024-04-22T20:13:44.231Z [MUXER0] Removed source priority 1
2024-04-22T20:13:44.231Z [MUXER0] Set visible priority to 150
2024-04-22T20:13:44.231Z [HYPERHDR0] New priority[150], previous [1]
2024-04-22T20:13:44.231Z [COLORSPACE_CALIBRATION0] (ColorSpaceCalibration.cpp:225) setBackLightEnabled: 1
2024-04-22T20:13:48.184Z [MUXER0] Register new input 'Web Configuration@::ffff:192.168.1.45/COLOR' with priority 1 as inactive
2024-04-22T20:13:48.184Z [MUXER0] Priority 1 is now active
2024-04-22T20:13:48.184Z [MUXER0] Set visible priority to 1
2024-04-22T20:13:48.184Z [HYPERHDR0] New priority[1], previous [150]
2024-04-22T20:13:48.184Z [COLORSPACE_CALIBRATION0] (ColorSpaceCalibration.cpp:225) setBackLightEnabled: 0
2024-04-22T20:13:55.373Z [FLATBUFSERVER] (FlatBufferServer.cpp:138) New connection from ::ffff:127.0.0.1
2024-04-22T20:13:55.373Z [FLATBUFSERVER] (FlatBufferServer.cpp:138) New connection from ::ffff:127.0.0.1
2024-04-22T20:13:55.373Z [FLATBUFSERVER] (FlatBufferServer.cpp:138) New connection from ::ffff:127.0.0.1
2024-04-22T20:13:55.373Z [FLATBUFSERVER] (FlatBufferServer.cpp:138) New connection from ::ffff:127.0.0.1
2024-04-22T20:13:55.373Z [FLATBUFSERVER] (FlatBufferServer.cpp:138) New connection from ::ffff:127.0.0.1
2024-04-22T20:13:55.374Z [FLATBUFSERVER] (FlatBufferServer.cpp:138) New connection from ::ffff:127.0.0.1
2024-04-22T20:13:55.374Z [FLATBUFSERVER] (FlatBufferServer.cpp:138) New connection from ::ffff:127.0.0.1
2024-04-22T20:13:55.374Z [FLATBUFSERVER] (FlatBufferServer.cpp:138) New connection from ::ffff:127.0.0.1
2024-04-22T20:13:55.374Z [FLATBUFSERVER] (FlatBufferServer.cpp:138) New connection from ::ffff:127.0.0.1
2024-04-22T20:13:55.374Z [FLATBUFSERVER] (FlatBufferServer.cpp:138) New connection from ::ffff:127.0.0.1
2024-04-22T20:14:01.857Z [COLORSPACE_CALIBRATION0] (ColorSpaceCalibration.cpp:241) setBrightness: 100
2024-04-22T20:14:01.859Z [COLORSPACE_CALIBRATION0] (ColorSpaceCalibration.cpp:252) setBrightnessCompensation: 0
2024-04-22T20:14:01.860Z [CHANNEL_CYAN0] (ChannelCalibration.cpp:70) setAdjustment: [0, 255, 255, active]
2024-04-22T20:14:01.864Z [CHANNEL_MAGENTA0] (ChannelCalibration.cpp:70) setAdjustment: [255, 0, 255, active]
2024-04-22T20:14:01.866Z [CHANNEL_BLUE0] (ChannelCalibration.cpp:80) setCorrection: 255
2024-04-22T20:14:01.867Z [CHANNEL_GREEN0] (ChannelCalibration.cpp:80) setCorrection: 255
2024-04-22T20:14:01.868Z [CHANNEL_RED0] (ChannelCalibration.cpp:80) setCorrection: 255
2024-04-22T20:14:01.869Z [CHANNEL_WHITE0] (ChannelCalibration.cpp:70) setAdjustment: [255, 255, 255, active]
2024-04-22T20:14:01.871Z [CHANNEL_YELLOW0] (ChannelCalibration.cpp:70) setAdjustment: [255, 255, 0, active]
2024-04-22T20:14:03.057Z [COLORSPACE_CALIBRATION0] (ColorSpaceCalibration.cpp:241) setBrightness: 100
2024-04-22T20:14:03.059Z [COLORSPACE_CALIBRATION0] (ColorSpaceCalibration.cpp:252) setBrightnessCompensation: 0
2024-04-22T20:14:03.061Z [CHANNEL_CYAN0] (ChannelCalibration.cpp:70) setAdjustment: [0, 255, 255, active]
2024-04-22T20:14:03.076Z [CHANNEL_MAGENTA0] (ChannelCalibration.cpp:70) setAdjustment: [255, 0, 255, active]
2024-04-22T20:14:03.084Z [CHANNEL_BLUE0] (ChannelCalibration.cpp:80) setCorrection: 255
2024-04-22T20:14:03.086Z [CHANNEL_GREEN0] (ChannelCalibration.cpp:80) setCorrection: 255
2024-04-22T20:14:03.088Z [CHANNEL_RED0] (ChannelCalibration.cpp:80) setCorrection: 255
2024-04-22T20:14:03.090Z [CHANNEL_WHITE0] (ChannelCalibration.cpp:70) setAdjustment: [255, 255, 255, active]
2024-04-22T20:14:03.091Z [CHANNEL_YELLOW0] (ChannelCalibration.cpp:70) setAdjustment: [255, 255, 0, active]
2024-04-22T20:14:12.015Z [MUXER0] (Muxer.cpp:123) Source auto select is now disabled
2024-04-22T20:14:12.015Z [MUXER0] Set visible priority to 150
2024-04-22T20:14:12.015Z [HYPERHDR0] New priority[150], previous [1]
2024-04-22T20:14:12.015Z [COLORSPACE_CALIBRATION0] (ColorSpaceCalibration.cpp:225) setBackLightEnabled: 1
2024-04-22T20:15:14.061Z [FLATBUFSERVER] (FlatBufferClient.cpp:92) Socket Closed
2024-04-22T20:15:14.062Z [FLATBUFSERVER] (FlatBufferClient.cpp:92) Socket Closed
2024-04-22T20:15:14.062Z [MUXER0] Removed source priority 150
2024-04-22T20:15:14.062Z [MUXER0] (Muxer.cpp:297) The manual selected priority '150' is no longer available, switching to auto selection
2024-04-22T20:15:14.063Z [MUXER0] (Muxer.cpp:123) Source auto select is now enabled
2024-04-22T20:15:14.063Z [MUXER0] Set visible priority to 1
2024-04-22T20:15:14.063Z [HYPERHDR0] New priority[1], previous [150]
2024-04-22T20:15:14.063Z [COLORSPACE_CALIBRATION0] (ColorSpaceCalibration.cpp:225) setBackLightEnabled: 0
2024-04-22T20:15:14.069Z [FLATBUFSERVER] (FlatBufferClient.cpp:92) Socket Closed
2024-04-22T20:15:14.071Z [FLATBUFSERVER] (FlatBufferClient.cpp:92) Socket Closed
2024-04-22T20:15:14.075Z [FLATBUFSERVER] (FlatBufferClient.cpp:92) Socket Closed
2024-04-22T20:15:15.580Z [FLATBUFSERVER] (FlatBufferServer.cpp:138) New connection from ::ffff:127.0.0.1
2024-04-22T20:15:15.580Z [FLATBUFSERVER] (FlatBufferServer.cpp:138) New connection from ::ffff:127.0.0.1
2024-04-22T20:15:15.580Z [FLATBUFSERVER] (FlatBufferServer.cpp:138) New connection from ::ffff:127.0.0.1
2024-04-22T20:15:15.580Z [FLATBUFSERVER] (FlatBufferServer.cpp:138) New connection from ::ffff:127.0.0.1
2024-04-22T20:15:15.580Z [FLATBUFSERVER] (FlatBufferServer.cpp:138) New connection from ::ffff:127.0.0.1
2024-04-22T20:15:15.580Z [FLATBUFSERVER] (FlatBufferServer.cpp:138) New connection from ::ffff:127.0.0.1
2024-04-22T20:15:15.581Z [FLATBUFSERVER] (FlatBufferServer.cpp:138) New connection from ::ffff:127.0.0.1
2024-04-22T20:15:15.581Z [FLATBUFSERVER] (FlatBufferServer.cpp:138) New connection from ::ffff:127.0.0.1
2024-04-22T20:15:15.581Z [FLATBUFSERVER] (FlatBufferServer.cpp:138) New connection from ::ffff:127.0.0.1
2024-04-22T20:15:15.581Z [FLATBUFSERVER] (FlatBufferServer.cpp:138) New connection from ::ffff:127.0.0.1
2024-04-22T20:15:15.623Z [FLATBUFSERVER] (FlatBufferServer.cpp:138) Previous line repeats 28 times
2024-04-22T20:15:15.623Z [FLATBUFSERVER] (FlatBufferClient.cpp:92) Socket Closed
2024-04-22T20:15:15.625Z [FLATBUFSERVER] (FlatBufferClient.cpp:92) Socket Closed
2024-04-22T20:15:15.626Z [FLATBUFSERVER] (FlatBufferClient.cpp:92) Socket Closed
2024-04-22T20:15:15.628Z [FLATBUFSERVER] (FlatBufferClient.cpp:92) Socket Closed
2024-04-22T20:15:15.631Z [FLATBUFSERVER] (FlatBufferClient.cpp:92) Socket Closed
2024-04-22T20:15:15.632Z [FLATBUFSERVER] (FlatBufferClient.cpp:92) Socket Closed
2024-04-22T20:15:15.633Z [FLATBUFSERVER] (FlatBufferClient.cpp:92) Socket Closed
2024-04-22T20:15:15.634Z [FLATBUFSERVER] (FlatBufferClient.cpp:92) Socket Closed
2024-04-22T20:15:15.636Z [FLATBUFSERVER] (FlatBufferClient.cpp:92) Socket Closed
2024-04-22T20:15:15.637Z [FLATBUFSERVER] (FlatBufferClient.cpp:92) Socket Closed
2024-04-22T20:15:16.007Z [FLATBUFSERVER] (FlatBufferClient.cpp:92) Previous line repeats 33 times
2024-04-22T20:15:16.007Z [FLATBUFSERVER] (FlatBufferServer.cpp:138) New connection from ::ffff:127.0.0.1
2024-04-22T20:15:16.032Z [MUXER0] Register new input 'webos@::ffff:127.0.0.1/FLATBUFSERVER' with priority 150 as inactive
2024-04-22T20:15:16.033Z [MUXER0] Priority 150 is now active
2024-04-22T20:19:04.276Z [WEBSOCKET] (HyperAPI.cpp:1109) message: [{"command":"leddevice","ledDeviceType":"","params":{},"subcommand":"hasLedClock","tan":1}]
2024-04-22T20:19:27.642Z [IMAGETOLED_MNG0] (ImageToLedManager.cpp:192) Set LED mapping type to multicolor_mean
2024-04-22T20:19:27.642Z [IMAGETOLED_MNG0] Total index number is: 14720 (memory: 14720). User sparse processing is: disabled, image size: 320 x 180, area number: 135
2024-04-22T20:19:27.642Z [IMAGETOLED_MNG0] (ImageToLedManager.cpp:176) setSparseProcessing to 0
2024-04-22T20:19:27.644Z [COLORSPACE_CALIBRATION0] classicMode: no, gammas:[1.50, 1.50, 1.50], saturation: 1.00, luminance: 1.00, backLight: [enabled, threshold: 1, colored: yes]
2024-04-22T20:19:27.644Z [LED_CALIBRATION0] (LedCalibration.cpp:101) Calibration config '0' for LED segment: [0, 134]
2024-04-22T20:19:27.646Z [LED_CALIBRATION0] (LedCalibration.cpp:96) LedCalibration is released
2024-04-22T20:19:53.052Z [IMAGETOLED_MNG0] (ImageToLedManager.cpp:176) setSparseProcessing to 0
2024-04-22T20:19:53.052Z [COLORSPACE_CALIBRATION0] classicMode: yes, gammas:[1.50, 1.50, 1.50], saturation: 1.00, luminance: 1.00, backLight: [enabled, threshold: 1, colored: yes]
2024-04-22T20:19:53.053Z [LED_CALIBRATION0] (LedCalibration.cpp:101) Calibration config '0' for LED segment: [0, 134]
2024-04-22T20:19:53.053Z [LED_CALIBRATION0] (LedCalibration.cpp:96) LedCalibration is released
2024-04-22T20:20:04.602Z [MUXER0] (Muxer.cpp:123) Source auto select is now disabled
2024-04-22T20:20:04.602Z [MUXER0] Set visible priority to 150
2024-04-22T20:20:04.602Z [HYPERHDR0] New priority[150], previous [1]
2024-04-22T20:20:04.602Z [COLORSPACE_CALIBRATION0] (ColorSpaceCalibration.cpp:225) setBackLightEnabled: 1
2024-04-22T20:20:18.573Z [MUXER0] Register new input 'System/SYSTEMGRABBER' with priority 245 as inactive
2024-04-22T20:20:18.573Z [COMPONENTCTRL0] System capture device: enabled
2024-04-22T20:20:27.577Z [NETFORWARDER] Forwarder has changed state to disabled
2024-04-22T20:20:27.577Z [COMPONENTCTRL0] Json/Proto forwarder: disabled
2024-04-22T20:20:30.851Z [MUXER0] Removed source priority 240
2024-04-22T20:20:30.851Z [COMPONENTCTRL0] Video capture device: disabled
2024-04-22T20:20:35.341Z [MUXER0] Removed source priority 245
2024-04-22T20:20:35.341Z [COMPONENTCTRL0] System capture device: disabled
2024-04-22T20:20:37.036Z [MUXER0] Register new input 'System/SYSTEMGRABBER' with priority 245 as inactive
2024-04-22T20:20:37.036Z [COMPONENTCTRL0] System capture device: enabled
2024-04-22T20:21:01.282Z [IMAGETOLED_MNG0] (ImageToLedManager.cpp:192) Set LED mapping type to advanced
2024-04-22T20:21:01.282Z [IMAGETOLED_MNG0] Total index number is: 14720 (memory: 14720). User sparse processing is: disabled, image size: 320 x 180, area number: 135
2024-04-22T20:21:03.013Z [IMAGETOLED_MNG0] (ImageToLedManager.cpp:192) Set LED mapping type to weighted
2024-04-22T20:21:03.014Z [IMAGETOLED_MNG0] Total index number is: 14720 (memory: 14720). User sparse processing is: disabled, image size: 320 x 180, area number: 135
2024-04-22T20:21:17.498Z [PERFORMANCE] [INSTANCE0: FPS = 48.13, processed = 2888]
2024-04-22T20:21:17.498Z [PERFORMANCE] [INSTANCE0: FPS = 48.13, processed = 2888], [LED0: FPS = 98.13, send = 5888, processed = 2888, dropped = 0]
2024-04-22T20:22:17.493Z [PERFORMANCE] [INSTANCE0: FPS = 48.22, processed = 2893], [LED0: FPS = 98.22, send = 5893, processed = 2893, dropped = 0]
2024-04-22T20:22:45.217Z [WEBSOCKET] (HyperAPI.cpp:1109) message: [{"command":"leddevice","ledDeviceType":"adalight","subcommand":"discover","tan":904}]
2024-04-22T20:22:45.278Z [WEBSOCKET] (HyperAPI.cpp:1133) response: [{"devices":[{"name":"Auto","value":"auto"},{"name":" (/dev/ttyS0)","value":"ttyS0"},{"name":" (/dev/ttyS1)","value":"ttyS1"},{"name":"Pico (/dev/ttyACM0)","value":"ttyACM0"}],"ledDeviceType":"adalight"}]
2024-04-22T20:23:17.503Z [PERFORMANCE] [INSTANCE0: FPS = 48.28, processed = 2897], [LED0: FPS = 98.25, send = 5896, processed = 2897, dropped = 0]
2024-04-22T20:24:17.502Z [PERFORMANCE] [INSTANCE0: FPS = 48.18, processed = 2891], [LED0: FPS = 98.18, send = 5891, processed = 2891, dropped = 0]
2024-04-22T20:24:32.657Z [WEBSOCKET] (HyperAPI.cpp:1109) message: [{"command":"leddevice","ledDeviceType":"","params":{},"subcommand":"hasLedClock","tan":1}]
2024-04-22T20:25:17.494Z [PERFORMANCE] [INSTANCE0: FPS = 48.27, processed = 2896], [LED0: FPS = 98.28, send = 5896, processed = 2896, dropped = 0]
2024-04-22T20:25:51.953Z [MUXER0] Removed source priority 1
2024-04-22T20:26:17.489Z [PERFORMANCE] [INSTANCE0: FPS = 48.07, processed = 2884], [LED0: FPS = 98.07, send = 5884, processed = 2884, dropped = 0]
2024-04-22T20:26:37.212Z [MUXER0] (Muxer.cpp:123) Source auto select is now enabled
2024-04-22T20:26:58.283Z [MUXER0] Register new input 'Web Configuration@::ffff:192.168.1.45/COLOR' with priority 1 as inactive
2024-04-22T20:26:58.283Z [MUXER0] Priority 1 is now active
2024-04-22T20:26:58.283Z [MUXER0] Set visible priority to 1
2024-04-22T20:26:58.283Z [HYPERHDR0] New priority[1], previous [150]
2024-04-22T20:26:58.283Z [COLORSPACE_CALIBRATION0] (ColorSpaceCalibration.cpp:225) setBackLightEnabled: 0
2024-04-22T20:27:18.278Z [PERFORMANCE] [INSTANCE0: FPS = 32.19, processed = 1957], [LED0: FPS = 82.19, send = 4996, processed = 1957, dropped = 0]
2024-04-22T20:27:22.622Z [MUXER0] Removed source priority 1
2024-04-22T20:27:22.622Z [MUXER0] Set visible priority to 150
2024-04-22T20:27:22.622Z [HYPERHDR0] New priority[150], previous [1]
2024-04-22T20:27:22.622Z [COLORSPACE_CALIBRATION0] (ColorSpaceCalibration.cpp:225) setBackLightEnabled: 1
2024-04-22T20:27:22.912Z [WEBSOCKET] (WebSocketClient.cpp:188) send close: 1000
2024-04-22T20:27:24.957Z [WEBSOCKET] (WebSocketClient.cpp:39) New connection from ::ffff:192.168.1.45
2024-04-22T20:28:17.487Z [PERFORMANCE] [INSTANCE0: FPS = 44.23, processed = 2619], [LED0: FPS = 94.24, send = 5580, processed = 2619, dropped = 0]
2024-04-22T20:29:17.490Z [PERFORMANCE] [INSTANCE0: FPS = 48.18, processed = 2891], [LED0: FPS = 98.18, send = 5891, processed = 2891, dropped = 0]
2024-04-22T20:29:32.535Z [SMOOTHING0] Clearing queued colors before: disabling
2024-04-22T20:29:32.535Z [SMOOTHING0] Smoothing queue is cleared
2024-04-22T20:29:32.535Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:297) Disable the device
2024-04-22T20:29:32.535Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:381) Stopping refresh timer
2024-04-22T20:29:32.535Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:90) Switch off
2024-04-22T20:29:32.535Z [LEDDEVICE0_ADALIGHT] (LedDevice.cpp:544) Set LED strip to black/power off
2024-04-22T20:29:32.539Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:146) Flush was successful
2024-04-22T20:29:32.548Z [LEDDEVICE0_ADALIGHT] Received goodbye: 'HyperHDR frames: 99 (FPS), receiv.: 99, good: 99, incompl.: 0, mem1: 0, mem2: 448, heap: 123232
' (97)
2024-04-22T20:29:32.553Z [LEDDEVICE0_ADALIGHT] (ProviderSerial.cpp:164) Serial port is closed: ttyACM0
2024-04-22T20:29:32.553Z [COMPONENTCTRL0] LED device: disabled
2024-04-22T20:29:32.553Z [PERFORMANCE] [INSTANCE0: FPS = 48.18, processed = 2891]
2024-04-22T20:29:35.555Z [MUXER0] Removed source priority 245
2024-04-22T20:29:35.555Z [COMPONENTCTRL0] System capture device: disabled
2024-04-22T20:30:17.491Z [PERFORMANCE] [INSTANCE0: FPS = 48.13, processed = 2888]
2024-04-22T20:31:17.487Z [PERFORMANCE] [INSTANCE0: FPS = 48.52, processed = 2911]
2024-04-22T20:32:17.495Z [PERFORMANCE] [INSTANCE0: FPS = 48.49, processed = 2910]
2024-04-22T20:33:13.636Z [WEBSOCKET] (WebSocketClient.cpp:39) New connection from ::ffff:192.168.1.37
2024-04-22T20:33:17.493Z [PERFORMANCE] [INSTANCE0: FPS = 48.18, processed = 2891]
2024-04-22T20:33:41.544Z [WEBSOCKET] (HyperAPI.cpp:957) log streaming activated for client ::ffff:192.168.1.37
2024-04-22T20:34:17.498Z [PERFORMANCE] [INSTANCE0: FPS = 48.23, processed = 2894]
2024-04-22T20:34:41.635Z [WEBSOCKET] (HyperAPI.cpp:957) log streaming activated for client ::ffff:192.168.1.45
2024-04-22T20:35:17.494Z [PERFORMANCE] [INSTANCE0: FPS = 48.17, processed = 2890]
2024-04-22T20:36:17.501Z [PERFORMANCE] [INSTANCE0: FPS = 48.39, processed = 2904]
2024-04-22T20:37:17.500Z [PERFORMANCE] [INSTANCE0: FPS = 48.23, processed = 2894]
2024-04-22T20:38:17.500Z [PERFORMANCE] [INSTANCE0: FPS = 48.33, processed = 2900]
2024-04-22T20:39:17.492Z [PERFORMANCE] [INSTANCE0: FPS = 48.26, processed = 2895]
2024-04-22T20:39:21.827Z [WEBSOCKET] (WebSocketClient.cpp:39) New connection from ::ffff:192.168.1.37
2024-04-22T20:39:22.267Z [WEBSOCKET] (HyperAPI.cpp:957) log streaming activated for client ::ffff:192.168.1.37

[awawa-dev]

You missed one zero in Baud rate : 200000
If after you correct it there is no change, unfortunately you won't be able to do without a level shifter (just avoid i2c level shifters)

[ancylow]

Thanks. I was trying differents combinations, that's because baudrate were changed. 2000000 has same result.
Now I set the IP of my libreelec installation in Piccap, an works fine with Arduino board.
But I want to remove devices, I will look for a board that can manage with TV's USB.
Thanks for your support.

[lucasfeijo]

@ancylow Did you figure this out? I'm trying to make the LG tv see this board https://www.amazon.com/dp/B0CYKYDH64 it has an esp32-C3 and I installed hyperserial on it from here https://github.com/awawa-dev/HyperSerialWLED but I think hyperhdr isn't seeing the board as a valid tty option.